A standard 35mm die-cast zinc pole socket is provided in the bottom of the enclosure so it can be mounted above a sub or on a tripod. For installations, a wall-mount bracket is available.
The amplifier consists of 2 channels with a total of 700W.
The amplifier features extremely high dynamic power capacity, with 85 Volts peak output per channel, along with high damping of >10,000:1 Efficient, PFC power supply and class D output topology.
Exceptional dynamic resolution and detail along with precise control. Low current draw and light weight relative to the output capacity.
All the processing necessary for linear frequency response and phase coherent operation are pre-programmed into the DSP. With the comprehensive processing built in, BASSBOSS loudspeakers provide the ease of plug-and-play operation and the peace of mind that comes from knowing that the multiple limiter systems make to system virtually indestructibl
Electrical power is converted into acoustical energy by an 8″ neodymium motor woofer.
These premium-quality, drivers feature 2″ copper voice coils, and peak-to-peak excursion capability of up to 16mm.
High-intensity Neodymium magnets are lighter and provide higher efficiency so the result is a lighter and louder cabinet. A copper shorting cap provides for increased high frequency response and reduced distortion and a ventilated voice coil gap improves cooling and reduces thermal compression.
High frequencies are handled by a 1″ throat compression driver featuring a 36mm aluminum voice coil and a Mylar diaphragm mounted to a 90 degree by 60 degree rotatable horn.
The cones are waterproofed to protect them from possible, accidental exposure to moisture such as rain or spilled beverages. Waterproofed woofer cones also permit the cleaning of drivers that have been soiled in a dirty or dusty environment with the use of a damp cloth. Keep the amplifiers dry and party on!
Waterproofed cones in all products. Optional weatherized and weather resistant loudspeakers have the same acoustical performance as our standard options. If your system is likely to be exposed to rain, ask about IP rated amplification options. If you have need of a system for outdoor installation, ask about Weatherized products.
BASSBOSS speakers can be connected directly to your mixer with nothing but signal cable in between. The built-in processing is comprehensive and includes all necessary high-pass and low-pass filters along with equalization and phase alignment processing to ensure coherent response when deployed with BASSBOSS subwoofers.
There is no need for any additional EQ in the signal path for the speaker to provide a broad, flat frequency response. Sophisticated DSP programming ensures the speakers deliver consistent sound quality no matter the input level.
Plug-and play with peace of mind. Multiple, sophisticated protection systems make the loudspeaker virtually indestructible. You can turn on and turn up, all night, without fear of over-driving to the point of damage.
BASSBOSS technical specs are based upon measurements of continuous performance capabilities in normal usage. Other manufacturers may specify output based on calculations rather than measurements; measurements outside the operating bandwidth; or on ‘Burst’ or ‘Peak’ readings.
BASSBOSS specifications are conservative compared to most manufacturers. They reflect what the products will achieve, consistently, in the real world. Since the real world is where you’ll be using your gear.
- Dimensions: 18" x 9.5" front, 7" rear, x 14" (HxWxD)
- Frequency response (+-3 dB): 50 - 19,000 Hz (full range)
- Maximum sustained output: 112dB SPL, 1m, 2pi, half-space
- Short-term peak output: 118dB
- Net weight: 26 lbs.
- Shipping weight: 31 lbs.
- Grill: Perforated, powder-coated steel
- Amplifier: 700W - two channel powersoft class D amplifier
- DSP: Integrated comprehensive DSP for HP, LP, phase alignment, EQ and limiting
- Electrical connectors, amplifier: Neutrik Powercon
- Electrical connector, mains: Nemas-15 (Edison) standard 3-pin grounded plug
- Voltage operating range: 90 - 250V auto-sensing, auto switching pfc universal supply
- Current draw, nominal: 1.6A @ 1/8 power
- Signal input connector: XLR-F
- Signal output connector: XLR-M pass-through only